Mold remediation referrals for Fort Worth & nearby townsCall: (817) 518-2276
(817) 518-2276

How much does mold remediation cost in Fort Worth?

moldremediationfortworth.net

Published Fort Worth cost guides put whole-job mold remediation between $1,500 and $6,000, with a per-square-foot range of $9 to $18. Your own number depends on how much material is affected, where the mold is, and what has to be rebuilt afterward.

Need mold help now?
Call now to be connected with a local mold remediation company in Fort Worth.
(817) 518-2276

Published Fort Worth cost guides put whole-job mold remediation between $1,500 and $6,000, with a per-square-foot range of $9 to $18. Your own number depends on how much material is affected, where the mold is, and what has to be rebuilt afterward.

Quick cost estimator

Typical ranges from the sources cited below, not a quote. The company you hire will price the actual job.

The short answer

Two Fort Worth cost guides give the clearest picture for this area. One puts remediation at roughly $9 to $18 per square foot of affected area for the Dallas-Fort Worth market. The other describes a typical whole-job range of $1,500 to $6,000, depending on severity and area. Those are published estimates, not quotes, and your price can fall outside them. For comparison, national figures are lower for the overall job ($1,125 to $3,345) and higher per square foot ($15 to $30), which is a good reminder that the two ways of pricing a job do not line up neatly.

The calculator on this page lists each range side by side and states the area each one covers. Treat it as a way to sanity-check a written quote, not a way to predict one.

What the price is really built from

Remediation is mostly labor, containment and disposal. A crew has to seal off the work area, run negative air so spores are not pushed into clean rooms, remove or clean affected material, and then dry and clean the space. A small patch behind a toilet and a mold problem across a ceiling and two walls are very different jobs even if both start with the same dark stain.

  • Size of the affected area. Per-square-foot pricing rises with the amount of material involved, but small jobs often hit a minimum charge because setup costs the same either way.
  • Material type. Mold on the surface of framing can be cleaned. Mold that has soaked into drywall, insulation or carpet padding usually means removal and replacement.
  • Access. A hot attic, a tight crawl space or a wall cavity that has to be opened all add time.
  • The water source. If the moisture problem has not been fixed, the price of cleanup is only part of the bill. A leaking supply line or a failed roof section has to be repaired by the right trade before remediation can hold.
  • Rebuild work. Many remediation quotes cover removal and cleaning only. New drywall, paint, insulation and flooring are often separate line items.

Typical ranges by location in the home

Some places cost more because the work is harder. These ranges are national figures from a published cost guide, since the Fort Worth pages we reviewed did not break costs out by room:

  • Partial attic: $1,500 to $6,000. A full attic runs $6,000 to $15,000, higher with extensive damage or insulation replacement. North Texas attics get very hot and carry air handlers and ductwork, so roof leaks and condensation can both show up here. See our page on attic mold removal in Fort Worth.
  • HVAC system or ducts: $2,000 to $10,000, depending on system type and how far the growth has spread. Our guide to mold in your AC, attic air handler and ducts explains where it tends to start.
  • Crawl space: $1,500 to $4,000 for remediation depending on size and accessibility, with a lower $500 to $2,000 figure published for crawl space remediation only, not encapsulation. Many local homes are slab-on-grade, but older pier-and-beam houses do have crawl spaces.
  • Black mold: $2,000 to $10,000 in any area, reflecting removal difficulty. The color is not what drives the price, as explained in black mold facts.

What inspection and testing add

Costs often start before the cleanup does. A national guide lists a mold inspection at $300 to $650, covering a visual check, moisture readings, sampling if suspected and a written report. Air sampling runs $100 to $300 per test and surface sampling $50 to $200 per test in the same source. Those are separate from remediation.

In Texas, that separation is built into the rules. A person generally cannot do both the mold assessment and the remediation on the same project, so expect two different companies and two different invoices on a larger job. If you want to understand what the assessment step produces and why it is not the same as a lab sample, read mold inspection vs mold testing. For the rules on who may do each part, see Texas mold license rules. You can also look at the Fort Worth mold inspection page to see how a visit is usually structured.

No clearance testing price turned up in the pages we reviewed, so we do not quote one here. Ask any company for a written figure. Clearance is explained in post-remediation clearance testing.

When the work is under 25 square feet

TDLR says visible mold under 25 contiguous square feet can be cleaned up by people without a license, including an owner or maintenance staff. EPA's guide is more conservative, saying a homeowner can usually handle an area smaller than about 10 square feet. If your problem is small and on a hard surface, that may be your lowest-cost path. Our DIY vs professional guide goes through where the line really sits. Past it, the job needs a mold remediation company that holds a TDLR mold license.

How to compare quotes fairly

Quotes that look far apart are often quoting different jobs. Before you compare totals, line up the scope.

  1. Ask for the assessor's protocol first. On larger projects the protocol tells every bidder what to remove, what to clean and where containment goes. Bids written against the same protocol are directly comparable.
  2. Get a written work plan. TDLR says the remediation contractor creates a customized work plan that follows the protocol, and both documents must reach the client at least one calendar day before work starts.
  3. Check what is excluded. Does the price include removing and replacing drywall, insulation, trim and flooring, or only demolition and cleaning?
  4. Ask how the water problem is handled. A quote that ignores the source of moisture is incomplete.
  5. Verify the license. Look up the company on TDLR's Verify a License search before you sign anything.

If your issue came from water damage, the water damage mold service page shows how drying and remediation fit together. And if it followed a storm or flooding, our first 48 hours after a North Texas storm or flood guide covers what to do before the quotes start.

Ways to keep the final bill reasonable

Most of the savings come from acting early and from stopping the moisture, not from haggling. EPA says it is important to dry water-damaged areas and items within 24 to 48 hours to prevent mold growth, and a wet wall dried on day two is a much smaller job than the same wall left for two weeks. Keep a record of when the water event happened, photograph everything before anything is removed, and keep receipts for emergency drying. If a condensate line or a roof leak caused the problem, get that repaired first so you are not paying twice for the same cleanup. Finally, ask whether the company can separate the work into phases, so you can see which items are removal and which are rebuild.

Does location inside the metro change the price?

The published ranges are for the Dallas-Fort Worth market as a whole, so we cannot say that a job in one town costs more than in another. Travel, parking, home size and age all play a role. If you live in Arlington or Dallas and compare notes with a neighbor across the county line, expect differences that come from the scope of work, not the zip code. You can start from the pages for Arlington or Dallas and from the full list of services to see which job type matches what you found.

Insurance and who pays

Whether a policy pays for mold depends on the cause of the loss and the policy's own terms, so check with your insurer before work starts. If you rent, the repair duty is separate: under Texas Property Code 92.052 a landlord must make a diligent effort to repair a condition when the tenant has given notice and is current on rent, and the condition materially affects the physical health or safety of an ordinary tenant. That duty does not apply to conditions the tenant, occupants or guests caused beyond normal wear and tear. Our guide to mold in a Texas rental covers the basics.

Next step

If you have a mold problem and want a local company to look at it, you do not have to start by hunting through listings.

Call now to be connected with a local mold remediation company in Fort Worth.
(817) 518-2276
Describe what you found and the call is routed to an independent local company that handles your area. Mold Removal Fort Worth is a referral service, not a mold company, and the price is set between you and the company you speak with.

Frequently asked questions

How much does mold remediation cost in Fort Worth?
A Fort Worth cost guide gives about $9 to $18 per square foot of affected area, and another describes a typical whole-job range of $1,500 to $6,000. These are published estimates for the Dallas-Fort Worth market, not quotes.
Is mold inspection included in the remediation price?
Usually not. A national guide lists inspection at $300 to $650 as its own cost, and in Texas the assessor and the remediation company generally cannot be the same business on one project.
Why are two quotes so different?
They often cover different scopes. One may include rebuilding drywall and insulation while another covers only removal and cleaning, or they may assume different containment. Ask both to quote against the same written protocol.
Do I need a company with a TDLR mold license for a small job?
TDLR says visible mold under 25 contiguous square feet can be cleaned up by people without a license. Larger projects need a mold remediation company that holds a TDLR mold license.
Does homeowners insurance pay for mold cleanup?
It depends on what caused the damage and on your policy language, so ask your insurer before work begins and keep written records of the damage and the quotes.
Call now to be connected with a local mold remediation company in Fort Worth.
(817) 518-2276

Last updated:

☎ Call (817) 518-2276